lusMizo tawng

Power battery testing principle leh method bulpui ber berte chu engte nge ni?

Dec 03, 2025

Message pakhat dah la .

Power battery testing principle leh method bulpui ber berte chu engte nge ni?

 

Power Battery Testing chungchanga thu bulpui leh hmanraw hman dan

 

Chemical power source-a electrochemical property bulpui ber berte chu capacity, voltage, internal resistance, self-discharge, storage performance, high leh low temperature performance, etc. Secondary chemical power source pangngai angin power battery-ah hian charge leh discharge performance, cycle performance, internal pressure, etc. te pawh a tel a, chuvangin, power battery cell pakhat tana performance testing content lian ber berte chu: charge leh discharge performance testing, discharge performance testing, discharge capacity leh rate performance testing, temperature sang leh hniam performance testing, energy leh specific energy testing, power leh specific power testing, storage performance leh self-discharge testing, life testing, internal resistance testing, internal pressure testing, leh safety testing, etc.

 

Lirthei hman tak takna a\\ang chuan lirthei hmanna atana \\ha test hrang hrang chu electric lirtheia hman tur power battery pack hmangin test object atan an ti a, chungte chu: static capacity detection, dynamic capacity detection, quiescent test, starting power test, rapid charging capability test, cycle life test, safety test, battery vibration test, peak power detection, partial discharge detection, maximum gradient power test, thermal performance test te hi a ni test, etc. tih a ni.

Power Battery Testing
Power Battery Testing

(1) Static Capacity hriat theihna He test hian a tum ber chu lirthei hman tak tak laiin power battery pack hian charge leh energy a nei tling tih hriat a ni a, discharge rate leh temperature hrang hrang ruat lawk hnuaiah pawh a pangngaiin hna a thawk thei tih hriat a ni. Test dan ber chu temperature awm reng hnuaia slow discharge testing a ni a, power battery pack voltage chu set value-a a tlahniam emaw, power battery pack chhunga cell pakhat chauh consistency (voltage danglamna) set value a thlen chuan discharge chu tihtawp a ni.

 

(2) Dynamic Capacity hriat theihnaElectric lirthei a kal lai hian power battery hnathawhna temperature leh discharge rate chu a inthlak danglam nasa hle. He test hian dynamic discharge condition hnuaia power battery pack thiltihtheihna a hmuchhuak ber a, hei hi temperature leh discharge rate hrang hranga energy leh capacity-ah a lang ber a ni. Test dan ber chu power battery pack discharge performance testing chu current profile ruat lawk emaw, lirthei application atanga current profile lakkhawm tak tak emaw hmanga tih a ni. Test termination condition hi test condition leh power battery characteristics a zirin siamrem a ni a, mahse a bul berah chuan voltage value engemaw zat a tlahniam standard a zawm thung. Hetiang method hian electric lirthei hmanna mamawh tak tak chu direct leh dik zawkin a tarlang thei a ni.

 

(3) Quiescent Test tih a niHe test hian a tum ber chu power battery pack chu hun engemaw chen hman loh huna a capacity hloh dan hriatchhuah a ni a, hei hi electric lirthei chu hun engemaw chen khalh loh a, battery chu inhawng-circuit-a dah a nih dan simulate nan hman a ni. Quiescent test hi self-discharge and storage performance test tia hriat a ni bawk a, hei hian battery chu open-circuit state-a a awm laiin environmental condition thenkhat hnuaia a charge dahkhawm chu a vawng reng thei tih a kawk a ni.

 

(4) Power Test tan tir Car starting power hi a lian tawk a, temperature hrang hrang hnuaia car starting nena inmil theih nan power battery pack-ah hian temperature hniam ($−18\\text{℃}$) leh temperature sang ($50\\text{℃}$)-ah starting power test an nei thin. He test hi room temperature-a teh a nih bakah, a tlangpuiin battery charge state hrang hranga discharge theihna hriat theihna turin SOC value nen pawh set a ni. Test hman tlanglawn ber chu $90\\%$, $50\\%$, leh $20\\%$ SOC-a power test neih thin a ni.

 

(5) Rapid Charging theihna TestHe test hian a tum ber chu power battery pack-a high-rate charging test hmanga battery charging chakna test a ni a, a efficiency, heat generation leh property dangte chunga nghawng a neih dan enfiah a ni. Rapid charging atan chuan USABC standard hian battery SOC hi $15\\text{min}$ chhungin $40\\%$ atanga $80\\%$ thlenga recover a tum a ni. Tunah hian Japan-a CHAdeMO association-in standard a siamah chuan electric vehicle power battery pack chu $10\\text{min}$ vel a charge chuan lirthei chu $50\\text{km}$ vel a kal theihna tur a ni tih a sawi a $30\\text{min}$ aia tam charge chuan lirthei chu $100\\text{km}$ a kal tih a tichiang thei.

 

(6) Cycle Nunna TestBattery cycle life hian battery hmanna economic viability a nghawng nghal vek a ni. Battery capacity tak tak chu a tir lama capacity emaw rated capacity emaw $80\\%$ aia hniam a nih chuan power battery chu a dam chhung tawp thlenga ngaih a ni. He test-a hman dan ber chu condition thenkhatah charge leh discharge cycle tih a ni a, cycle zat chu a dam chhung index atan hman a ni. Power battery dam chhung test hun chhung hi a rei deuh avangin test hi a tlangpuiin thla engemaw zat emaw kum khat emaw pawh a ni. Chuvangin, practical operation-ah chuan test cycle awm zat tehna, capacity degradation tehna, chu data hmanga linear extrapolation tih dan te chu test nan hman a ni fo thin. Research lamah chuan power battery test hun tihtlem nan power battery leh power battery pack dam rei zawng test nan test temperature leh charge/discharge rate tihsan a, battery aging chak zawkna tur zirchianna neih mek a ni bawk.

 

(7) Hriselna TestBattery safety performance tih hian storage battery dahkhawm leh hman avanga mi leh hmanrua te tana harsatna awm thei tehna a kawk a ni. A bik takin battery hman sual a nih chuan energy input bik hian battery chhunga thil awmte chu physical emaw chemical reaction emaw a tawk a, chu chuan lumna nasa tak a siam chhuak thin. A hun taka lumna chu a bo thei lo a nih chuan battery thermal runaway a thlen thei a ni. Thermal runaway hian battery a ti bulh thei a, gas kang thei a siam thei a, a ti chhe thei a, a chhe thei a, kangmei pawh a zui thei a, safety accident a thlen thei bawk. Chemical power source tam tak zingah hian lithium-ion battery himna hi a pawimawh hle. Power battery-a safety testing item hman tlanglawn tak takte chu Table 6-1-ah hian tarlan a ni.

 

Power Battery Testing

 

Table 6-1 Power Battery-a himna test-na hmanraw hman tlanglawn

 

Bithliahna Test dan tlangpui
Electrical hnathawh dan Test Overcharge, over-discharge, pawn lam short circuit, hot discharge, etc. te hi a ni.
Mechanical hmanga test a ni Free fall, impact, extrusion, vibration, extrusion, etc. te pawh a awm thei.
Thermal Test hmanga enfiah a ni Kang, thermal imaging, thermal shock, temperature inthlak danglamna, etc.
Environment Test a ni Vacuum simulation, immersion, humidity, etc. hmanga siam a ni.

 

(8) Battery Vibration TestHe test hian a tum ber chu kawngpui vanga vibration leh shock awm fo hian power battery leh power battery pack te performance leh life a nghawng dan hriatchhuah a ni. Battery vibration test hian power battery (pack) vibration durability a enfiah ber a, hei hi power battery (pack) structural design tihchangtlunna tur kaihhruaina atan a hmang a ni. Vibration test-naah hian vibration chi hnih a awm a, chungte chu sinusoidal vibration emaw random vibration emaw an ni. Power battery pack hi lirtheia hman a nih ber avangin battery hnathawh dan tak tak simulate tha zawk nan random vibration hi hman a ni tlangpui.

 

A chunga kan sawi takte hi power battery (pack) test na atana thil tul tlangpui thenkhat chauh a ni. Test-na atana parameter leh mamawh bikte chu power battery chi hrang hrang a zirin a inang lo ang. Table 6-2-ah hian electric lirtheia hman tur lithium-ion battery pack leh system-te himna lama performance mamawh leh test dan tur tarlan a ni.

 

Table 6-2 Electric Vehicle-a Lithium-ion Battery Pack leh System-a Safety Performance mamawh leh Test dan

 

Thil Bithliahna Test dan tur Hriselna atana thil tulte
Safety Test hman tlanglawn tak (Table 6-1) 1.1. Electrical hnathawh dan Test Overcharge, over-discharge, pawn lam short circuit, hot discharge, etc. te hi a ni. N/A
  Mechanical hmanga test a ni Free fall, impact, extrusion, vibration, extrusion, etc. te pawh a awm thei. N/A
  Thermal Test hmanga enfiah a ni Kang, thermal imaging, thermal shock, temperature inthlak danglamna, etc. N/A
  Environment Test a ni Vacuum simulation, immersion, humidity, etc. hmanga siam a ni. N/A
EV Li-ion Battery himna (Table 6-2) 1. A rilru a hah lutuk chuan a rilru a buai em em a. Vibration a awm 1. Test Object: Battery Pack emaw System. 1. Lirthei dahna tur mamawh leh GB/T 2423.43-2008, vibration table-a install tur en rawh. Kawng 3 ($Y \\to X \\to Z$) ah test rawh. Procedure hian GB/T a kawk 2423.56-2018. 2. Lower-body installation tan chuan GB/T 31467.3-2015. 3.-a 7.1.1.2 angin test parameters chu test hun hi direction khatah $2\\text{h}$ a ni ($0.5\\text{h}$-ah tihhniam theih a ni). $2\\text{h}$ observation phalsak a nih lai emaw, a hnuah emaw $30\\text{min}$. 4. Monitoring unit dinhmun tlem ber (voltage, resistance, temp) enfiah. 5. Test laiin $2\\text{h}$ enfiah. 6.Electronic hmanrua atan chuan:Ka. Front-mounted: GB/T 31467.3-2015-a 7.1.1.2.1 khata test. Hmun dang: Test per GB/T 28046.3-2011. $2\\text{h}$ chu $Z$-axis lam hawi hrang hrangah a awm. Lateral objects: excitation mode kalpui a ni. ii. GB/T khatah $3.2$ mode-in a thawk thei 28046.1-2011. Battery pack emaw system emaw chu: Minimum monitoring unit ($)-ah voltage decay a nei lo tur a ni< 0.5\text{V}$), remain intact, structure sound, no leakage, no rupture, fire, or explosion. Insulation resistance $\ge 100\text{Ω}/\text{V}$ within $30\text{min}$ after test. Electronic devices: Reliable connection, structure sound, no disconnection. Post-test parameters meet Table 1 in GB/T 31467.3-2015.
  Mechanical Shock a ni 1. Test Object: Battery Pack emaw System. 2. 7.2 Shock $25\\text{g}\\text{-}15\\text{ms}$ half-sine pulse in GB/T 31467.3-2015, $3$ shock te chu $Y$-axis lam hawiin, $2\\text{h}$ en rawh. Leakage, outer casing rupture, kangmei, puak thei lo. Insulation do theihna $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Far 1. Test Object: Battery Pack emaw System. 2. $1\\text{m}$ atanga hard ground-ah drop theihna tur lam hawia tlak (chuti lo chuan drop direction stable ber, $X$-axis test), $2\\text{h}$ en rawh. Discharge current lock, voltage surge emaw leakage emaw, pawn lam casing rupture, kangmei, puak emaw a awm lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Rollover a ni . $2\\text{h}$. 3. en rawh $360\\text{℃}$ $X$-axis vel chu $6\\text{℃}/\\text{s}$-ah rotate la, chutah chuan $90\\text{℃}$ increment-ah rotate la, $1\\text{h}$ ve ve vawng tlat la, $360\\text{℃}$ rotation chu tihtawp a ni. $2\\text{h}$. 4. en rawh $360\\text{℃}$ $Y$-axis vel chu $6\\text{℃}/\\text{s}$-in rotate la, chutah $90\\text{℃}$ increment-in, $1\\text{h}$ ve ve vawng la, $360\\text{℃}$ rotation chu tihtawp a ni. $2\\text{h}$ chu enfiah rawh. Leakage, outer casing rupture, kang, leh puak, connection rintlak tak a awm lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Gradient sang ber a ni 1. Test Object: Battery Pack emaw System. 2. Trolley-a dinglam hawia dah. SAE J2380 emaw GB/T 31467.3-2015-a Table 7-a Fig 3-a tarlan pulse chu $2\\text{h}$ tan ($X$-axis $5\\text{s}$ zawhin, $Y$-axis $5\\text{s}$-ah) kalna lam hawi ($Y$-axis)-ah tih leh rawh. Leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Tikehsawm 1. Test Object: Battery Pack or System. 2. Crush conditions: ① Crushing surface: $12.5\text{mm}$ diameter semi-cylinder, length $>$ zau zawng. 2 A kalna tur: $X$-axis, $Y$-axis. 3 Force: A tir lamah $200\\text{kN}$ emaw $30\\%$ deformation-ah tihtawp emaw. 4 $1\\text{h}$ chu enfiah rawh. 5 $10\\text{min}$ atan hold rawh. Leakage, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni. Kangmei leh puak thei lo (requirement set hnihna atan).
  Temperature Shock a ni 1. Test Object: Battery Pack emaw System. 2. Temperature inthlak danglam $(-40\\pm2)\\text{℃}$, max $30\\text{min}$ hun chhung extreme-ah. $6\\text{h}$, $5$ cycle atan extreme tinah dah rawh. Room temp-ah $2\\text{h}$ chu enfiah rawh. Leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Damp Heat Cycle a ni 1. Test Object: Battery Pack emaw System. 2. GB/T 2423.4-2018 Test $Db$ damp heat cycles en rawh. GB/T 31467.3-2015 ($80\\text{℃}$ max temp)-a Figure 4-ah hian, $5$ cycle-ah a lang. Room temp-ah $2\\text{h}$ chu enfiah rawh. Leakage, outer casing rupture, kangmei, puak thei lo. Test zawhah $30\\text{min}$ chhungah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Tuipui tuiah Immersion 1. Test Object: Battery Pack emaw System. 2. Harness connected hmanga him taka khin, $3.5\\%$ NaCl solution (tuipui tui)-ah $2\\text{h}$-in transport distance tak takah thun rawh. Hydraulic valve form hmangin suspend rawh. Kangmei leh puak pawh a awm lo.
  Pawn lam Mei 1. Test Object: Battery Pack emaw System. 2. GB/T 31467.3-2015-a 7.10 External Fire en rawh. Kangmei leh puak pawh a awm lo. Flame a awm chuan, fire source lakchhuah hnuah $2\\text{min}$ chhungah a thi tur a ni.
  Salt Spray hmanga siam a ni 1. Test Object: Battery Pack emaw System. 2. GB/T 31467.3-2015-a 7.11 Salt Spray en rawh. Leakage, outer casing rupture, kangmei, puak thei lo.
  Altitude sang takah a awm 1. Test Object: Battery Pack emaw System. 2. Altitude $4000\\text{m}$ emaw a tlukpui pressure, room temperature. 3. GB/T 31467.3-2015-a 7.12.2 khatah test environment-ah $5\\text{h}$-in dah a ni a, chutah chuan $1\\text{C}$ (max $400\\text{A}$) emaw to cut-off a ni. $2\\text{h}$ chu enfiah rawh. Discharge current lock, voltage surge emaw leakage emaw, pawn lam casing rupture, kangmei, puak emaw a awm lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Over-temperature atanga venhimna 1. Test Object: Battery System. 2. GB/T 31467.3-2015-a 7.13 Over-temperature Protection en rawh. BMS hian hna a thawk ang. Gas leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Short Circuit hmanga venhimna a ni 1. Test Object: Battery System. 2. GB/T 31467.3-2015-a Short Circuit venhimna 7.14 en rawh. Protection device a thawk tur a ni. Leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Overcharge hmanga venhimna a ni 1. Test Object: Battery System. 2. GB/T 31467.3-2015-a Overcharge Protection 7.15 en rawh. BMS hian hna a thawk ang. Gas leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.
  Over-discharge Invenna 1. Test Object: Battery System. 2. GB/T 31467.3-2015-a 7.16 Over-discharge Protection en rawh. BMS hian hna a thawk ang. Gas leakage, outer casing rupture, kangmei, puak thei lo. Test hnuah insulation resistance $\\ge 100\\text{Ω}/\\text{V}$ a ni.

 

Power Battery Testing

 

Note: Table 6-2 hian GB/T 31467.3-2015, GB/T 2423.43-2008, GB/T 2423.56-2018, leh GB/T 28046.1-2011 te a tarlang ber a ni.

Inquiry thawn rawh .